smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.18.34-20.el6.x86_64] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" HDD MK.002TSKB Device Model: TOSHIBA MK2002TSKB Serial Number: 92M2KGN9F LU WWN Device Id: 5 000039 44b783842 Firmware Version: MT4A User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Fri Sep 9 22:38:34 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 367) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 096 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 11627 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 4 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 146 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 2588 10 Spin_Retry_Count 0x0033 100 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 4 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 5 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 52 (Min/Max 27/60) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 110 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 1467 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 19 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 4131 222 Loaded_Hours 0x0032 094 094 000 Old_age Always - 2588 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 98 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 65535 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 65535 occurred at disk power-on lifetime: 2587 hours (107 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 72 40 22 c5 40 Error: UNC at LBA = 0x00c52240 = 12919360 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 80 80 3f 23 c5 40 00 16d+06:25:01.571 READ FPDMA QUEUED 60 80 78 bf 22 c5 40 00 16d+06:25:01.571 READ FPDMA QUEUED 60 80 70 3f 22 c5 40 00 16d+06:25:01.571 READ FPDMA QUEUED 60 80 68 3f 28 c5 40 00 16d+06:25:01.570 READ FPDMA QUEUED 60 80 60 bf 27 c5 40 00 16d+06:25:01.570 READ FPDMA QUEUED Error 65534 occurred at disk power-on lifetime: 2587 hours (107 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 1a c9 21 c5 40 Error: UNC at LBA = 0x00c521c9 = 12919241 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 80 18 bf 21 c5 40 00 16d+06:24:55.262 READ FPDMA QUEUED 60 80 10 3f 22 c5 40 00 16d+06:24:55.262 READ FPDMA QUEUED 60 80 08 bf 22 c5 40 00 16d+06:24:55.262 READ FPDMA QUEUED 60 80 00 3f 23 c5 40 00 16d+06:24:55.262 READ FPDMA QUEUED 60 80 f0 bf 23 c5 40 00 16d+06:24:55.262 READ FPDMA QUEUED Error 65533 occurred at disk power-on lifetime: 2587 hours (107 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 0a 4e 21 c5 40 Error: UNC at LBA = 0x00c5214e = 12919118 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 80 90 bf 29 c5 40 00 16d+06:24:47.587 READ FPDMA QUEUED 60 80 88 3f 29 c5 40 00 16d+06:24:47.587 READ FPDMA QUEUED 60 80 80 bf 28 c5 40 00 16d+06:24:47.587 READ FPDMA QUEUED 60 80 78 3f 28 c5 40 00 16d+06:24:47.587 READ FPDMA QUEUED 60 80 70 bf 27 c5 40 00 16d+06:24:47.587 READ FPDMA QUEUED Error 65532 occurred at disk power-on lifetime: 2587 hours (107 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 a2 08 21 c5 40 Error: UNC at LBA = 0x00c52108 = 12919048 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 f0 ff e6 9f 40 00 16d+06:24:28.962 READ FPDMA QUEUED 60 20 e8 5f e6 9f 40 00 16d+06:24:28.962 READ FPDMA QUEUED 60 80 e0 bf 1d c5 40 00 16d+06:24:28.962 READ FPDMA QUEUED 60 80 d8 3f 1e c5 40 00 16d+06:24:28.962 READ FPDMA QUEUED 60 80 d0 bf 1e c5 40 00 16d+06:24:28.962 READ FPDMA QUEUED Error 65531 occurred at disk power-on lifetime: 2587 hours (107 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 da d8 1c c5 40 Error: UNC at LBA = 0x00c51cd8 = 12917976 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 f0 df e6 9f 40 00 16d+06:24:21.560 READ FPDMA QUEUED 60 20 38 bf e6 9f 40 00 16d+06:24:21.560 READ FPDMA QUEUED 60 20 30 9f e6 9f 40 00 16d+06:24:21.560 READ FPDMA QUEUED 60 20 28 7f e6 9f 40 00 16d+06:24:21.560 READ FPDMA QUEUED 60 20 00 5f e6 9f 40 00 16d+06:24:21.560 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.